人工在线翻译中译英
发布网友
共2个回答
热心网友
The charging socket into socket in the shell of tank. Take the 2 ST3*8 screws for electric screwdriver into the charging socket cover is fastened to the lower cover. The battery assembly to cover the battery slot gap, black connection card into the battery slot. The motor assembly mounted to the lower cover, determine the motor installed in place. The connecting wire is straightened out, tied together by tie. The main PCB button button holes aligned indicating lamp shade, which is arranged to indicate the lampshade, buckles fasten the PCB board card indicating lamp. The indicator card to the lamp groove indicating lampshade, lamp and the lamp groove face flush. A switch button is pressed, the switch button is not on the PCB lamp posts to. The cover is mounted to the top cover, buckle card into the slot.
The upper cover to cover. The bottom face up in the tooling, the 5 ST3*12 fastening screw to screw the cover for electric screwdriver. The st cup mounted to the machine. The fan blades are flat down to under ultrasonic tooling mold. Wind leaf convex super, 3 holes at the wind leaves 3 fixed columns on the wind leaf. My hands start ultrasonic tool, the blade cover is fixed to the wind leaf. The fan component fixed blade cover. The st cup sleeve to the ultrasound tooling die. The trademark cover as shown in the direction of the st cup trademark cover groove. My hands start ultrasonic tool, the trademark cover to the st cup. Dust cup assembly.
The st cup figure mounted ultrasonic tooling die fixed. The st cup mouth is arranged to st groove cup mouth. The film covers the st cup, the hands start ultrasonic tool, the st cup mouth is fixed to the st cup. Ultrasonic good st cup mouth st cup assembly. The st cup as icon sets the direction to the fixture mould. The front wheel of the big end of the flat end into the front wheel, rotate the wheel to determine wheel to rotate smoothly, then the front wheel flat alignment st cup shaft hole wear to the st cup. The hands press tooling button, the axle pressure to the st cup. Pressure wheel st cup assembly. The stproof plug to an air inlet st cup. The filter screen seat and the inner component self out. 3.6V.
With a clean cloth to the st cup of oil dirt, clean. The nameplate label affixed to the bottom of the label groove. Take color tape is folded 20mm, then the switch will be bubble color tape switch button on the back of the machine, as shown in the diagram of protective bubble edge to switch from the visual is greater than 5mm, with the tape around a circle of fixed. Round the elevator tie to elevator inside. Handle the elevator tie line to the upper. The whole into a plastic bag (Note: the elevator on the bottom). The conical bubble as shown by color tape is fixed on the paper tray. Will the st cup upwards, according to shape into a paper holder (elevator discharge.
The box marks affixed to the box at the bottom of the box, the box according to the folding into graphic shape, according to the sequence shown folded at the bottom. The Russian brochure, manual, warranty card such as graphics and fold. The manual assembly as shown in figure into the next, then the box from top to bottom to the whole. The manual, warranty card, Russian pamphlets as shown stacked together, the sticker box (as shown), then the box from top to bottom are installed. The upper cover is covered on the paper box, button to Caconne. The box on the electronic scale weighing, no leakage or is installed accessories. The outer box according to the folding into shape. The box with tape to the bottom.
The box on the electronic scale weighing, no leakage or is installed accessories. The outer box according to the folding into shape. The outer box at the bottom of the tape to seal a way. Will be installed to the outer box 6 box machine, box direction to be consistent. The upper cover is covered outside the box, to the word the way sealed with tape. The outer box neatly placed on pallets.
热心网友
Put the charging socket to socket shell under the slot. 2 of the ST3 * 8 fastening screws with electric screwdriver outlet cover to cover. The battery cover assembly to the battery card slot, the gaps between the black cable card to the card slot battery. Will the motor cover component is installed to the next, determine the motor installed in place. The connector straighten out, with tie together. Aim the main PCB button indicates the button hole of the lampshade, to be loaded on the indicator lamp shade, indicating lamp shade card buckle buckle PCB. Indicator card to indicate the lamp chamfer of the lampshade, lamp and lamp chamfer end face flush. The press of a button, the button is not on the PCB light switches is determined to resist. From cover to cover, button card card to the slot. On the cover to cover. Use the machine bottom up on tooling, electric screwdriver to five ST3 * 12 screw fastening cover under the machine screw hole. The st cup on the machine. The blades under the flat side down on the ultrasonic tooling mould. Blades lid convex super, three holes on the blades of three fixed column on the blades. Hands start ultrasonic tooling, cover the blades fixed on the blades. Fixed blades of wind component. The st cup set on ultrasonic tooling mould. Direction of the trademarks cover as shown on the st cup cover a trademark of the slots. Hands start ultrasonic tooling, the trademarks cover is fixed on the st cup. The st cup components. Will the st cup as shown in figure ways to ultrasonic tooling mould under fixed. Dust the st cup mouth to mouth of the slots. Take film cover on the st cup, hands start ultrasonic tooling, the st cup mouth is fixed on the st cup. Ultrasonic st cup mouth of st cup component. Will the st cup as shown direction to a fixture on the fixed mould. Take the lion's share of the front axle end once wheel through the plane of the end, turn the wheels to determine wheels rotate smoothly, and then the front axle of flat on the st cup of shaft hole wear on the st cup. Hands press tooling button and the wheel and axle pressure on the st cup. Good pressure wheel st cup components. The stproof plug loaded on the st cup of air inlet. Take after filter and filter elements in self-inspection. To filter components into 3.6 V after mesh seat, holding the filter elements are shown in direction of rotation, the filter elements within mesh card point card to card slot. After the components installed in the outside mesh screen. The filter elements into the st cup. With clean flannelette machine clean dirt, grease and st cup. The nameplate label to label the slots at the bottom of the machine. Take color tape folded 20 mm at one end, and then switch with color foam tape behind the machine switch button, as shown in protective bubble edge to switch from visual greater than 5 mm, with tape wrapped around a circle. The elevator cable tie fasten to the round hole elevator. The elevator cable tie to the handle of the machine. Will the machine in a plastic bag (note: the bottom of the elevator on the machine). The conical bubble such as graphic method is to use a fixed color tape in the paper. Will the machine of the st cup up, according to the shape into the paper holder (the bottom of the elevator on the machine). Will on the paper according to the shape at the top of st to st cup take color box shipping mark on the color with this graphic box, color box again into graphic shapes according to the crease and fold as shown at the bottom of the order. Russian pamphlets, brochures, warranty card, such as graphic way. Next to put the manual way of components as shown in figure in the whole machine, and then from top to bottom color box set on the machine. Take manuals, warranty CARDS, Russian pamphlets fold together, as seen here attach the carton (as shown), then the color box installed from top to bottom. On the cover on the color box, paper buckle buckle to the hole. Put the color box in electronic weighing on said, make sure no packing or more accessories. The carton according to crease fold into graphic shapes. The bottom of the carton with tape to seal a word way. The six color box outside to inside of the machine, the direction of the color box. On the cover on the carton, use tape to seal a word way. The carton of neatly put on the pallet.
